Display

Accessories

SMART DISPLAY This electronic module is an intelligent operator interface. The display informs the operator of the truck status in real time (BDI, HCs, operating modes, fault control). The membrane keypad is the interactive interface for operators and service engineers to customize truck setups and calibrate truck sensors. Main features 64 kbytes eeprom to record: Operator adjustable parameters truck fault logs truck hour counters operator password service password maintenance features BDI profiles Power supply 15 - 100V Communication CAN Bus RS232 - current loop only for handset and laptop Diplay Alphanumeric 2 lines 20 characters each line backlight Leds 6, red colour Dashboard membrane, 6 buttons Inputs 8 DIGITAL Input range -Batt +Batt Input Impedance max 47 KOhm Threshold level 10 Volt Outputs 2 ON-OFF NPN type 1,5 A 1 ON-OFF NPN type 100 mA Connectors Ampseal Protection class IP65	ECO SMART DISPLAY This electronic module is an intelligent operator interface. The graphic display informs the operator of the truck status in real time (BDI, HCs, operating modes, fault control). The Navipad is the interactive interface for operators and service engineers to interact with truck,setup and calibrate truck sensors. Main features digital control by micro controller flash memory operator adjustable parameters truck fault logs truck hour counters operator password service password maintenance features BDI profiles Power supply 15 - 100 Volt Communications CAN Bus RS232 - current loop only for handset and laptop Display graphic LCD 128x64 resolution backlight Leds 5, red colour Dashboard 5 buttons Navipad Connectors Minifit with rubber protection Protection class IP65	GRAPHIC SMART DISPLAY This electronic module is an intelligent operator interface with large viewer area. The graphic display informs the operator of the truck status in real time (BDI, HCs, operating modes, fault control). The 6 buttons permit the operators and service engineers to interact with truck,setup and calibrate truck sensors. Main features Technical details: I/O 4 analog/digital inputs 1 output to -Batt (2,0Amps) CONTROL - 16 bit micro controller - flash memory - operator adjustable parameters - truck fault logs - truck hour counters - operator password - service password - maintenance features - BDI profiles COMMUNICATION - CAN - RS232 - current loop only for handset and laptop DISPLAY Graphic LCD - 70x46,5 mm view area - 240x160 resolution - backlight LEDS 6, red colour DASHBOARD 6 push buttons CONNECTORS Minifit with rubber protection PROTECTION IP54

SICOS

This electronic module is an intelligent operator interface. The graphic display informs the operator of the truck status in real time (BDI, HCs, operating modes, fault control). The membrane keypad is the interactive interface for operators and service engineers to customize truck setups and calibrate truck sensors.

Inputs

18 DIGITAL

PNP Type VBatt
Input Impedance 10 KOhm
Threshold level 10 Volt

4 DIGITAL

NPN TYpe +5
Input Impedance 4,7 KOhm
Threshold level Analogue Input

5 ANALOGUE

0 - 5 Volt
Input Impedance > 100 KOhm

Normally used for finger tips
3 ANALOGUE

0 - 7,5 Volt
Input Impedance > 100 KOhm

Normally used for potentiometer (traction, brake,....)

OUTPUT

3 ON-OFF NPN type 500 mA - 48 Volt

Battery Level Indicator

This device is used for indication of battery capacity. It incorporates 5 LEDs: if the battery is fully charged, 4 green LEDs illuminate; as the battery capacity reduces, LEDs progressively switch-off; when the battery level reaches the lowest threshold, the red LED illuminates. The indicator may be provided with an internal relay that may be used to stop the lift or traction motor.

MDI

This indicator provides three main functions: battery state of charge indication, hour meter count, and information about the alarm status of the system. The MDI PRC indicator implements same functions as MDI. In addition it is able to drive two proportional valves and two ON/OFF valves. One unit provides single module indicator functions plus the control of an electro- hydraulic distributor.

MDI & MDI CAN Features

Supply voltage 24 ÷ 96 V
Dimensions: Ø52 x 35 mm

MDI PRC Features

Supply voltage 24 V
Dimensions: Ø52 x 63 mm

2 outputs for proportional valves : 2 A continuous (current control)
2 outputs for ON/OFF valves : 2 A continuous (pwm control)