In/Out; Master Controllers

Accessories

VCM Vehicle Control Master The VCM family is a group of I/O and valve controlles also including the vehicle control software capability. Depending on final application requirements different sets of I/O are available. Also available in double micro and/or double CAN architecture. General Characteristics Power supply: 24V, 36V, 48V, 72V, 80V Dimensions: 225 x 90 x 49 mm Connector: Ampseal 35 poles (35 + 23 poles in double connector version) Real Time Clock Built-in freewheeling diodes Ambient temperature range: -40° +40°C I/O 7 Digital inputs 2 Analog inputs 2 Outputs driving to – BATT (PWM voltage controlled, max 1A) 8 Outputs driving to –BATT with precise current feedback to control proportional hydraulic valves (up to 2A per output) 2 CAN interfaces +12V Output Power Supply (up to 500mA) +5V Output Power Supply (up to 150mA) Other features Can interface Serial link I/O double connector version 11 Digital input 10 Analog inputs 3 Outputs driving to – BATT (PWM voltage controlled, max 1A) 8 Outputs driving to –BATT with precise current feedback to control proportional hydraulic valves (up to 1,8A per output) 1 Outputs driving to –BATT with precise current feedback to control proportional valves (up to 4A ) 2 Incremental Encoder interface 2 CAN interfaces +12V Output Power Supply (up to 500mA) +5V Output power Supply (up to 150mA) Protection class: IP65	MHYRIO CB Mhyrio CB is an electronic module specifically designed for the control of hydraulic electrovalves. Tipically it is one of the nodes in an intelligent distribution system in wich different modules are connected via canbus. The Mhyrio CB unit has the advantage that it can easily be located near the actuators (hydraulic valves) thus reducing and optimizing wiring layout. General Characteristics Controls digital control by micro controller flash memory eeprom to record operator adjustable control parameters Communication CAN RS232 - current loop only for handset and laptop Inputs 3 DIGITAL Voltage range VBatt Input Impedance max 47 KOhm Threshold level 6 Volt 1 ANALOGUE 0 - 10 Volt, 3 wires Input Impedance > 100 KOhm Outputs 3 ON-OFF NPN 1.5 A 9 PROPORTIONAL 1.5 A EVP 1-2 function 1 EVP 3-4 function 2 EVP 5-6 function 3 EVP 7-8 function 4 EVP 9 function 5 Dimensions 82 x 197 x 59 mm Connector Ampseal Protection class: IP65	MHYRIO Flash Mhyrio flash is an electronic module specifically designed for the control of hydraulic electrovalves. Tipically it is one of the nodes in an intelligent distribution system in wich different modules are connected via canbus. The Mhyrio flash unit has the advantage that it can easily be located near the actuators (hydraulic valves) thus reducing and optimizing wiring layout. General Characteristics Power supply 15V - 100V Flash memory eeprom to record operator adjustable control parameters Communication CAN RS232 - current loop only for handset and laptop Inputs 8 DIGITAL PNP Type VBatt Input Impedance 10 KOhm Threshold level 6 Volt 2 ANALOGUE 0 - 10 Volt, 3 wires Input Impedance > 100 KOhm Encoder A and B 12 Volt PNP or NPN type open collector or push-pull Threshold 2,5 Volt Max Frequency 500 Hz Supply 12 V< 50 mA Outputs 3 ON-OFF NPN 1,5 A 8 PROPORTIONAL 1.5 A EVP 1-2 function 1 EVP 3-4 function 2 EVP 5-6 function 3 EVP 7-8 function 4 Function 3 and 4 are mutually exclusive Dimensions 125 x 215 x 55 mm	HVC Hydraulic valves controller HVC is an electronic module specifically designed for the control of hydraulic electrovalves. Tipically it is one of the nodes in an intelligent distribution system in wich different modules are connected via canbus. The HVC unit has the advantage that it can easily be located near the actuators (hydraulic valves) thus reducing and optimizing wiring layout. General Characteristics Power supply 12 - 24 Volt Controls digital control by micro controller flash memory eeprom to record operator adjustable control parameters Communication CAN RS232 - current loop only for handset and laptop Inputs 3 DIGITAL: Voltage range VBatt, Input Impedance max 10 KOhm, Threshold level 7 Volt 2 DIGITAL: 0-12 Volt, Input Impedance 10 KOhm 1 ANALOGUE: 0 - 10 Volt, Input Impedance > 100 KOhm Outputs 4 ON-OFF NPN 1,5 A 1 PROPORTIONAL NPN 0-1,5 A Dimensions 82 x 107 x 47 mm	CAN tiller & CAN encoder Designed to collect inputs and make them available via CAN in order to minimize the wiring General Characteristics I/O CAN Tiller 12 Digital inputs (input range: -Batt +Batt) 6 Analog inputs (input range: 0 12V) Analog inputs can be used also as Digital inputs Command devices supply 5V or 12V I/O CAN Encoder 2 Encoder inputs 6 Analog inputs (input range: 0 12V) Analog inputs can be used also as Digital inputs Command devices supply 5V or 12V Other features CAN bus interface SW Download via CAN bus